comp.os.linux.networking

> Please send the output from dmesg that occurs after the first message
> from the ssb module.

dmesg out after first ssb output:
ssb: Sonics Silicon Backplane found on PCI device 0000:01:09.0
ieee80211_crypt: registered algorithm 'NULL'
usb 1-1: new low speed USB device using uhci_hcd and address 4
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 16 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[e00ff800-
e00fffff] Max Packet=[2048] IR/IT contexts=[4/8]
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation

Yenta: CardBus bridge found at 0000:01:05.0 [161f:202f]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:05.0, mfunc 0x01001002, devctl 0x64
usb 1-1: configuration #1 chosen from 1 choice
bcm43xx driver
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000007
Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05
pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe00fffff
usbcore: registered new interface driver hiddev
input: HID 0461:4d09 as /devices/pci0000:00/0000:00:1d.0/
usb1/1-1/1-1:1.0/input/input5
b43-phy0: Broadcom 4306 WLAN found
input: USB HID v1.00 Mouse [HID 0461:4d09] on usb-0000:00:1d.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
phy0: Selected rate control algorithm 'simple'
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000325213700a29a]
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 1502068k swap on /dev/hda3. Priority:-1 extents:1 across:
1502068k
EXT3 FS on hda4, internal journal
input: PC Speaker as /devices/platform/pcspkr/input/input6
input: ImPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/
input/input7
lp: driver loaded but no devices found
Registered led device: b43-phy0:tx
Registered led device: b43-phy0:rx
Registered led device: b43-phy0:tx
Registered led device: b43-phy0:rx
Registered led device: b43-phy0:tx
Registered led device: b43-phy0:rx
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 19 (level, low) -> IRQ 19
ssb: Sonics Silicon Backplane found on PCI device 0000:01:06.0
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:03:25:12:99:75
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
b44: eth0: Link is down.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
realplay.bin[4549]: segfault at 00000050 eip b7f6b717 esp bff8b03c
error 4


chris